When LA4440 amplifier circuit is used in Bridge mode, it can give output power up to 19 Watt. This amplifier is capable to run easily up to 12 inch woofers.
The main reasons for using LA4440 is,
- Small pop noise at the time of power supply ON/OFF and good starting balance.
- Good ripple rejection : 46dB typical.
- Built-in protectors.
- Thermal protector.
- Over voltage and surge voltage protector.
- Pin-to-pin short protector.
Simple LA4440 amplifier circuit diagram
A readymade 2 channel (2 I.C) LA4440 audio amplifier is shown below.
Back side of the same LA4440 amplifier circuit board,
You can modify most readymade amplifier kit to LA4440 bridge amplifier circuit by simply cutting some PCB tracks and adding some jumpers, but that may vary board to board.
The image clearly shows, that a ripple rejection B.E choke transformer is added in series to the +ve supply.
This is required in every audio amplifiers as any ripple in DC can cause unwanted noise. The shown circuit has a pre-amplifier too, but that’s not our topic, pre-amplifiers will be discussed in other articles.
Comments on this article before 07-12-2011, here Jump to recent comments.
-
Dipankar Deb on October 25, 2010 - 4:44 pm
your project is so great.
-
Anish KS on October 25, 2010 - 9:46 pm
LA 4440. What the cost now ?, 10 years back i brought it in the range 40-50, circuit is simple, but output not much good
arupbsk Reply:
October 25th, 2010 at 10:07 pmNow it costs about 50, Nowadays 6283 audio amplifiers are spread allover, but they don’t have that much voltage bearing strength, nor the protection features. For a 8? mid-range and Woofer driving, I’d highly recommend it. -
kenith on November 18, 2010 - 12:45 pm
hello..
i found this readymade amp board.. but what bout the bass and treble adjustments??? only wired for volume is given..Arup Reply:
November 18th, 2010 at 2:38 pmYou can make a low cost effective bass treble circuit. Here -
sunny on February 12, 2011 - 7:13 pm
hi
i wana make amp so which is better ic 4440 and 6283
plz reply soonArup Reply:
February 12th, 2011 at 7:30 pmFor mini projects the 6283 is good. But for big projects, woofer-driving and for qood quality, you should use 4440 amplifier.sunny Reply:
February 17th, 2011 at 5:26 pm@admin, i need more information .iwana make amp mini 500 watt
plz tell me what i need but i donot know how to assemble it
plz help me
plz give me you number icall usunny Reply:
February 20th, 2011 at 7:25 pmhi
i have amp 3055 buit loud switch is not work.can u help me how to configer loud switch
reply soonArup Reply:
February 21st, 2011 at 8:33 amGive me more technical details about the amplifier and the loud switch through contact form @ https://www.circuitsdiy.com/about/sunny Reply:
March 24th, 2011 at 4:23 pm@admin, hi
i wanna buy a power amplifiers plz tell me who is the best i need more bass
1=12? woofer
1=8? mid
4 twitter
this is one speakerArup Reply:
March 24th, 2011 at 5:56 pm@sunny, 12? woofer is 16watt, 8? mid is 8watt. So, you need 24Watts rms for 100% volume. You should use TDA2030A based amplifier. That has 35Watt power output capability. -
ANKIT on March 16, 2011 - 5:37 am
where i can bye it ? big electronics store or small store?
-
yashwanth on March 19, 2011 - 4:24 pm
hello..need you help…in understanding what all i need to make the LA4440 a complete..amplifier..i am completely new to all this..but..want to start learning..from this
inexpensive…amp..kit…Arup Reply:
March 19th, 2011 at 5:02 pm@yashwanth, You need the following to make an amplifier by this kit.
1. The kit itself
2. Volume control Pot, (bass control pot optional)
3. A cabinet
4. A transformer and Bridge rectifier for 12Volt suply
5. Wires, etc…..yashwanth Reply:
March 20th, 2011 at 1:08 am@Arup Basak, Thanks yaar…will do it ..i am buying in right away from ebay..yashwanth Reply:
March 20th, 2011 at 1:24 am@Arup Basak,And one more thing..can you design and sell Vaccum tube amp kit..where the buyer has to just put in the tubes..and do some wiring and as for LA4440 we have…the user should be getting the tubes ,wire and volume control and a cabinet..will u help me…Arup Reply:
March 20th, 2011 at 8:16 am@yashwanth, Where would you get that vacuum tube capsules in today’s age? LOLMani Reply:
June 9th, 2011 at 11:45 amHi sir IC 4440 audio board la power supply ac volt kodukkanuma, dc volt kodukkanuna, dc aga iruntha athu eppadi kodukkanum, transformer value sollunga. Antha boardla DTS board mattalama,Arup Reply:
June 9th, 2011 at 12:23 pmdc supply ya eatho oru I.C (board )ku kudu , apro ni ac supply ya dc supply a rectifier moolama maathu, apo than ac use panna mudiyum, apro, nee DTS use pannalaam aana, nee input kudukurathu pre amplified signal ah irukanum ok? -
sunny on March 25, 2011 - 1:02 pm
hi
i wanna buy tda-2030a amp.plz tell me where i can buy this amp and what is the price
reply me soon
byeArup Reply:
March 25th, 2011 at 9:40 pm@sunny, The cost would be around 100 Rs for the amplifier board of single IC. I’ll make a article on it and publish it in this blog on Sun-Monday. Stay tuned. -
sunny on March 26, 2011 - 10:30 am
hi
i need 500 watt power amp where i can buy this amp and what is the cost plz reply me soonArup Reply:
March 26th, 2011 at 11:15 am@sunny, You require 500 watt PMPO amplifier, or 500Watt RMS? -
sunny on March 26, 2011 - 3:27 pm
hi
i need more power and more bass i need 500 watt rmsArup Reply:
March 26th, 2011 at 3:52 pm@sunny, Do you know about which you are talking, or are you mad.
500Watt RMS output can easily destroy a concrete house. For 500Watt RMS output you need an 10 feet diameter speaker. If you are going to be a terrorist by destroying buildings by 500Watt RMS output, then I’ll not help you anyways.
And if you are referring to 500Watt PMPO, then for your kind information, this 4440 amplifier can easily drive 2500Watt PMPO speaker system.sunny Reply:
March 26th, 2011 at 6:04 pm@Arup Basak,
ok
hey why r u not help me 500 watt rms plz tell me what is the best amp 500 watt rms
i cannot destroy some thing .plz tell me 4440 amp no china ok
and 4440 pcb higher endArup Reply:
March 26th, 2011 at 8:01 pm@sunny,
Well, 500Watt RMS output can’t be derived from 4440. It can be achieved with MOSFET, driver based amplifiers only.
For those types of complex circuits, I am referring you to another electronics site, which is only for audio electronics. You can find their 800watt RMS amplifier here, http://www.diyaudio.com/forums/aussie-amplifiers/170494-800-watt-mosfet-amplifier-module.html -
sunny on March 31, 2011 - 4:00 pm
hi
plz you tell me best amp for home
i wanna buyArup Reply:
March 31st, 2011 at 9:55 pm@sunny,
For readymade home use amplifier, buy Creative SBS series sound system which costs around
3000/- -
sunny on March 31, 2011 - 4:01 pm
replay me soon and what is the cost for higher 500 watt rms amp
plz help me -
iqubal on April 11, 2011 - 6:08 pm
THIS IS HIGH POWER PROJECT EXPLAIN :- LA-4440 IC BRIDGE AMPLIFIER 2NOS AND LA-3161-IC PRE AMPLIFIER / TAKE LINE OUT FROM CD PLAYER + POWER TRIK 4TRANSISTOR BASS AND TREBLE BORD + 0-12-5AMPS POWER SUPPLY CONNNECT AND ENJOY THE BASS AND TREBLE AND VOLUME QUALITY IT IS VERY VERY GOOD ( AVAILABLE IN SHANTHI ELECTRONICS KOLLAM KERALA )
-
Dhrubajyoti Dey on May 23, 2011 - 3:58 am
Dear Arup, which value of volume control pot i can use for this LA4440 Circuit ? can u please give me one bass treable circuit with Ic 4558. This 4+4 pin ic is a Stereo bass treable controller.
Arup Reply:
May 23rd, 2011 at 12:38 pmActually, Ic 4558 is a dual op-amp I.C. I have discussed a circuit for op-amp based bass treble controller previously based on LM741 IC, which is a single op-amp IC. (https://www.circuitsdiy.com/low-cost-effective-bass-treble-circuit-using-op-amp-741). If you can understand the logic used there, you can do it with IC 4558 yourself. And if you cant do that, I’ll help you.Arup Reply:
May 23rd, 2011 at 12:40 pmValue of volume, pot will be 22K or 47K linear. -
Mani on June 21, 2011 - 1:31 pm
Ic 4440 amplifierkku 12v transformer amps value enna? Immediately
Arup Reply:
June 22nd, 2011 at 11:13 amUse 12Volt atleast 2Amps transformer -
Sanchit on June 27, 2011 - 2:38 pm
plz help me!!!!
I made a 4440 STEREO amplifier.Its right output channel is working properly but a buzzing sound is coming from its left output whether some input signal is connected or not. I am sure that the buzzing sound is different from that of grounding problems.PLEASE tell me the possible defect whether it is some capacitor or else?????Arup Reply:
June 27th, 2011 at 3:45 pmBuzzing normally indicates fault in grounding. But in this case you are sure about grounding, so reply me if you are using LA4440 in bridge mode? or in Stereo mode? I’ll try my best to help you.Sanchit Reply:
June 28th, 2011 at 2:29 amhttp://3.bp.blogspot.com/_Hliq4TP7PlY/TU_OefqAmEI/AAAAAAAAACc/ctaAOk80d3E/s1600/12w+%2528+6W+%252B+6W+%2529+Stereo+Amplifier+Circuit+Diagram+using+LA+4440.jpgHere is the circuit diagram from where I made the 4440 stereo ampArup Reply:
June 28th, 2011 at 4:56 amThen you can check the capacitors by altering then from right to left channel. And yes, do provide a grounding by a 100K valued resistor from the input line.Sanchit Reply:
June 28th, 2011 at 1:22 pmthankss a lot Sir
I corrected the problem ,it was the faulty 100uf capacitor at the left output channel -
Abi on August 24, 2011 - 6:43 am
I want this board’s circuit diagram
pls help -
albakumar on November 7, 2011 - 12:00 pm
sir, 4440ic ku 12.0.12v 5amp us pannalama?
0.12v 5amp kum 12.0.12 5amp kum eathavathu different erukka? -
Subrata on November 21, 2011 - 10:00 pm
Hi Sunny you can use TAS5630 audio amp up to 600W R.M.S Out put.For circuite you also search With Google TAS5630.
Debabrota Dam says
Hello mr. arup will u post a good quality 5 band graphic equalizer circuit diagram please...
Debabrota Dam says
Hello Mr. Arup can u post a 5band graphic equalizer please...
raj singh says
hello sir, im purchase in LA4440 dual channel bord but how to add bass and treble control plz help me
Arup says
Add separate bass/treble circuit.
dharma says
mr arup i want high quqlity bass treble circuit diagram can you send me by mail .?
Arup says
There's one published in this website using LM741 IC. Use that.
SAIBAL ROY says
hi, Ms. Arup Basak, i made 4440 stereo amplifire, i use 12v 2 amp transformer to powering the circuit ,the sound is good amplifing but i face a problem ,when i increase the volume the sound is buzing please help me..
Arup says
Check with a voltmeter if voltage drops in sudden when increasing volume or not. I guess your power supply is insufficient.
Sandeep says
Hi Arup,
You are managing a very useful blog. Congrats for the same.
I am planning to buy/build a dual IC amplifier for home use. I would use the same for driving my speakers - Bass 12", Mid 6" and Dome Tweeter 1.25". I love loud but distortion free quality sound output with heavy bass.
Looking on the internet I found lots of chips that can be used. Some of them are:
TDA2030A
TDA7294
STK4141
STK4050
LM3875
LM1875
LA4440
6283
2N3055
TAS5630
Now I am confused as to which is good.
Hence I request you to please throw some light on varios aspects of the above chips.
Please let me know the following info on each of the chips mentioned above:
a. Sound Quality
b. RMS output
c. Price for a dual IC amp
d. Other aspects like Life of the IC, Ease of availability in India
Please put in your thoughts. It will be of great help for me as well as for lots of followers of your blog.
You can also mail your thoughts to me at
Thanks,
Sandeep
Arup says
Hi Sandeep,
The IC, TDA2030A is the one most used in the industry because of it's good performance and low cost. I'd also recommend you using it. Note that it requires dual power supply.
Sandeep says
Hi Arup,
Thanks for your guidance.
But I have seen that amps based on 4440 and 6283 are commonly available in the market. However I did not find such amps which are basecd on 2030. Can you guide me to shops in Kolkata/Mumbai where I can get ready amps based on TDA2030.
Also please guide me on the Output/RMS of these three chips as well as your thoughts on the sound quality of these three chips.
- Sandeep
Arup says
4440 is a powerful one. You may go for it.
In Kolkata, goto chandni market and you'll get it in "Bengal Electronics" or any other shop.
Sandeep says
Final question .... Is TDA2030 better than 4440?
Arup says
In terms of cost/performance the TDA2030 is better than LA4440.
shridhar says
sir i have problem
sir how can i conncet bt board for la4440 dual ic audio amplifire show me in diagram
Hitesh Patel says
Hi Arup.....
i had a ready mate stereo amplifier with two nos of IC LA4440. it has 12volt, 2amp supply.
my question is that 12inch 300watt 8ohm woofer suitable for this Amplifier???
Also tell me 50W (25W+25W) Stereo Power Amplifier Circuit Diagram using STK4141 IC is suitable for that woofer?
Or tell me about oyher ICS which can suitable for 12inch 300watt 8ohm woofer ?
thank you...
please reply...
Hitesh Patel says
Hi Arup…..
tell me price of IC STK4191??
thank toy...
pranab says
I have a TDA2009A based amp (2 IC in stereo mode). I know it is not that powerful . I want to know is it possible to change this IC with a powerful one (say 4440 or something else) without changing any other component on the PCB ??
Is there any other option to make it more powerful ??
Am kind of feeling jealous bcoz my frnd got a new and powerful amp (transistroid based amp) RFT 2N3055 ..............lolzzzzz
Jass says
Hello sir i fitted 1230 dual ic . i have a problem..its sound like a radio station search ...?? what is the problem behind it. reply plz!!!!
Arnab says
That may be due to long connecting wires to the input. Or the power supply is pasaig some AC through it. Connect the negetive of the board to a earth.
Sattu says
Hi, I have an audio circuit which uses a pair of A1941 & C5198 transistors for audio output. Please help me with the output (RMS) of this circuit using these two transistor for one channel, another pair of A1941 & C5198 for second channel. Also would this provide a better output than IC 4440 in bridge mode as I have read in your post earlier that IC 4440 in bridge mode can give output upto 19W (RMS).
kapil says
Hello Arup,
I have an ic 4440 based amplifier and 0-12V 3A transformer for its supply both i was purchased from local market. I already have 2 speakers in which 1 tweeter 1 midrange and 1 12inch woofer per box. Now problem is that when I connect 1 speaker its sounds too good but when I connect both speaker its woofer sound is very low and distorted. Please suggest me which is weak, amplifier or supply. If amplifier, so suggest me which low cost amplifier is best for me.
sekhar says
Thanks sir, please give the circuit for TDA2030. (you suggested).
Vinod says
Sir, i buy a readymade sterio amp using 2 ic cd4440 .. The problem s loud humming when iam increasing the volume.. When iam touchin d cabin with my hand no change in humming i think no prblm in grounding. How can i correct it.. Suppy is 12v 5amps capacitor used in that is 25v,4700mf.. Pls help me sir..
Scot Maged says
With many car audio systems out there falling well short of tolerable a ideal solution is the addition of an amplifier. An amplifier can be used for one of two things. It can be used to power speakers the speakers that are in the cabin of the car or they can be used to power a sub-woofer in the boot of the car. Both uses provide a greater listening experience.;
Look over our very own web portal as well
<",http://www.caramoan.co/caramoan-hotels/